Light tubes

Light tubes or light pipes are used for transporting or distributing natural or artificial light. In their application to daylighting, they are also often called sun pipes, sun scopes, solar light pipes, or daylight pipes.

Generally speaking, a light pipe or light tube may refer to:

  • a tube or pipe for transport of light to another location, minimizing the loss of light;
  • a transparent tube or pipe for distribution of light over its length, either for equidistribution along the entire length (see also sulfur lamp) or for controlled light leakage.

Both have the purpose of lighting, for example in Architecture.

Materials and set-up Edit

Light tube with reflective material Edit

Bahnhof Berlin Potsdamer Platz Lichtröhre Straße Detail

A light tube installed in the subterranean train station at Potsdamer Platz, Berlin, seen from above ...

Berlin light tube

... and below ground.
(More images on Wikimedia Commons)

Also known as a "tubular skylight", "SunScope" or "Tubular Daylighting Device", this is the oldest and most widespread type of light tube used for daylighting. The concept was originally developed by the ancient Egyptians. The first commercial reflector systems were patented and marketed in the 1850s by Paul Emile Chappuis in London, utilising various forms of angled mirror designs. Chappuis Ltd's reflectors were in continuous production until the factory was destroyed in 1943.[1] The concept was rediscovered and patented in 1986 by Solatube International of Australia.[2] This system has been marketed for widespread residential and commercial use. Other daylighting products are on the market under various generic names, such as "SunScope", "solar pipe", "light pipe", "light tube" and "tubular skylight".

A tube lined with highly reflective material leads the light rays through a building, starting from an entrance-point located on its roof or one of its outer walls. A light tube is not intended for imaging (in contrast to a periscope, for example), thus image distortions pose no problem and are in many ways encouraged due to the reduction of "directional" light.

The entrance point usually comprises a dome (cupola), which has the function of collecting and reflecting as much sunlight as possible into the tube. Many units also have directional "collectors", "reflectors" or even Fresnel lens devices that assist in collecting additional directional light down the tube.

A set-up in which a laser cut acrylic panel is arranged to redirect sunlight into a horizontally or vertically orientated mirrored pipe, combined with a light spreading system with a triangular arrangement of laser cut panels that spread the light into the room, was developed at the Queensland University of Technology in Brisbane.[3] In 2003, Veronica Garcia Hansen, Ken Yeang, and Ian Edmonds were awarded the Far East Economic Review Innovation Award in bronze for this development.[4][5]

Light transmission efficiency is greatest if the tube is short and straight. In longer, angled, or flexible tubes, part of the light intensity is lost. To minimize losses, a high reflectivity of the tube lining is crucial; manufacturers claim reflectivities of their materials, in the visible range, of up to 98 to almost 99.5 percent.[6][7]

At the end point (the point of use), a diffuser spreads the light into the room.

To further optimize the use of solar light, a heliostat can be installed which tracks the movement of the sun, thereby directing sunlight into the light tube at all times of the day as far as the surroundings´ limitations allow, possibly with additional mirrors or other reflective elements that influence the light path. The heliostat can be set to capture moonlight at night.

Optical fiber Edit

Optical fibers are well known as fiberscopes for imaging applications and as light guides for a wide range of non-imaging applications. In the latter context, they can also be used for daylighting: a solar lighting system based on plastic optical fibers was in development at Oak Ridge National Laboratory in 2004;[8][9] the system was installed at the American Museum of Science and Energy, Tennessee, USA, in 2005,[10] and brought to market the same year by the company Sunlight Direct.[11][12]

A similar system, but using optical fibers of glass, had earlier been under study in Japan.[13]

In view of the usually small diameter of the fibers, an efficient daylighting set-up requires a parabolic collector to track the sun and concentrate its light.

Optical fibers intended for light transport need to propagate as much light as possible within the core; in contrast, optical fibers intended for light distribution are designed to let part of the light leak through their cladding.[14]

Transparent hollow light guides Edit

A prism light guide was developed in 1981[15] and has been used in solar lighting for both transport and distribution of light.[16][17] A large solar pipe based on the same principle has been set up in a narrow courtyard of a 14-floor building of a Washington D.C. law firm in 2001,[18][19][20][21][22] and a similar proposal has been made for London.[23] A further system has been installed in Berlin.[24]

The 3M company developed a system based on optical lighting film[25] and developed the 3M light pipe,[26] which is a light guide designed to distribute light uniformly over its length, with a thin film incorporating microscopic prisms,[15] which has been marketed in connection with artificial light sources, e.g. sulfur lamps.

In contrast to an optical fiber which has a solid core, a prism light guide leads the light through air and is therefore referred to as hollow light guide.

The project ARTHELIO,[27][28] partially funded by the European Commission, was an investigation in years 1998 to 2000 into a system for adaptive mixing of solar and artificial light, and which includes a sulfur lamp, a heliostat, and hollow light guides for light transport and distribution.

Fluorescence based system Edit

In a system developed by Fluorosolar and the University of Technology, Sydney, two fluorescent polymer layers in a flat panel capture short wave sunlight, particularly ultraviolet light, generating red and green light, respectively, which is guided into the interior of a building. There, the red and green light is mixed with artificial blue light to yield white light, without infrared or ultraviolet. This system, which collects light without requiring mobile parts such as a heliostat or a parabolic collector, is intended to transfer light to any place within a building. [29][30][31] By capturing ultraviolet the system can be especially effective on bright but overcast days; this since ultraviolet is diminished less by cloud cover than are the visible components of sunlight.

Properties and applications Edit

Solar and hybrid lighting systems Edit

Solar light pipes, compared to conventional skylights and other windows, offer better heat insulation properties and more flexibility for use in inner rooms, but less visual contact with the external environment.

In the context of seasonal affective disorder, it may be worth consideration that an additional installation of light tubes increases the amount of natural daily light exposure. It could thus possibly contribute to residents´ or employees´ well-being while avoiding over-illumination effects.

Compared to artificial lights, light tubes have the advantage of providing natural light and of saving energy. The transmitted light varies over the day; should this not be desired, light tubes can be combined with artificial light in a hybrid set-up.[16][32][33][34]

Some artificial light sources are marketed which have a spectrum similar to that of sunlight, at least in the human visible spectrum range,[35][36][37] as well as low flicker.[37] Their spectrum can be made to vary dynamically such as to mimick the changes of natural light over the day. Manufacturers and vendors of such light sources claim that their products can provide the same or similar health effects as natural light.[37][38][39] When considered as alternatives to solar light pipes, such products may have lower installation costs but do consume energy during use; therefore they may well be more wasteful in terms of overall energy resources and costs.

On a more practical note, light tubes do not require electric installations or insulation, and are thus especially useful for indoor wet areas such as bathrooms and pools. From a more artistic point of view, recent developments, especially those pertaining to transparent light tubes, open new and interesting possibilities for architectural design.

Security Applications Edit

Due to the relatively small size and high light output of sun pipes, they have an ideal application to security oriented situations, such as prisons, police cells and other locations where restricted access is required. Being of a narrow diameter, and not largely affected by internal security grills, this provides daylight to areas without providing electrical connections, escape access or objects to be passed into a secure area.

Light tubes in electronic devicesEdit

Molded plastic light tubes are commonly used in the electronics industry to conduct illumination from LEDs on a circuit board to indicator symbols or buttons. These light tubes typically take on a highly complex shape that uses either gentle curving bends as in an optic fiber or have sharp prismatic folds which reflect off the angled corners. Multiple light tubes are often molded from a single piece of plastic, permitting easy device assembly since the long thin light tubes are all part of a single rigid component that snaps into place.

Light tube indicators make electronics cheaper to manufacture since the old way would be to mount a tiny lamp into a small socket directly behind the spot to be illuminated. This often requires extensive hand-labor for installation and wiring. Light tubes permit all lights to be mounted on a single flat circuit board, but the illumination can be directed up and away from the board by several inches, wherever it is required.

See also Edit


  1. Science & Society Picture Library Advertisement for Chappuis’ patent reflectors, c 1851-1870.
  2. Solatube International, history
  3. Ken Yeang:Light Pipes: An Innovative Design Device for Bringing Natural Daylight and Illumination into Buildings with Deep Floor Plan, Nomination for the Far East Economic Review Asian Innovation Awards 2003
  4. Lighting up your workplace — Queensland student pipes light to your office cubicle, May 9, 2005
  5. Kenneth Yeang, World Cities Summit 2008, June 23—25, 2008, Singapore
  7. (French)
  8. Article on Hybrid Solar Lighting "Let the Sun Shine in", Discover Magazine, Vol. 25, No. 07, July 2004
  9. ORNL - Solar Technologies Program
  10. HSL Featured in Popular Science's What's New Section June 2005, Page 28
  11. Oak Ridge National Laboratory - New Oak Ridge company putting hybrid solar lighting on map
  12. Sunlight Direct- Architectural Design Information
  13. Hybrid Solar Lighting: Bringing a little sunshine into our lives, MSNBC, March 2005
  14. Use Of Diffusive Optical Fibers For Plant Lighting
  15. 15.0 15.1 Use Of Prismatic Films To Control Light Distribution
  16. 16.0 16.1 Solar Canopy Illumination: Solar Lighting at UBC
  17. research frame
  18. Solar Light Pipe in Washington, D.C
  19. - The International Design Magazine - Graphic Design, Product Design, Architecture
  21. Template:De icon
  22. "Solar Light Pipe in Washington, D.C.", DETAIL 4/2004, Building with light
  23. Apple London - Special Ceiling
  24. Template:De icon "Tageslicht aus der Tube", Faktor Licht, Nr. 4, 2003 (with a description of the light pipe on Potsdamer Platz, Berlin)
  25. Heliobus with 3M Optical Lighting Film (OLF)
  26. 3M Light Management Solutions (US)
  29. Fluorosolar
  30. FluoroSolar - bringing the subshine inside, Treehugger, February 5, 2006 (retrieved on January 13, 2007)
  31. Video on fluorescence based system
  32. Night Lite
  34. Sunlight Direct- Lighting Design Information
  35. True-Lite
  37. 37.0 37.1 37.2 Template:De icon
  38. Template:De icon
  39. Template:De icon

External links Edit

Overview Edit

Other approaches to sunlight capture and transmission Edit

Imported from Wikipedia

This page is being imported from Wikipedia, to create a Wikidwelling stub or article. These steps need to be completed:

  1. Sections not relevant to Wikidwelling can be deleted, or trimmed to a brief comment. Note: Image redlinks should not be removed
  2. Redlinks to articles unlikely to be created on Wikidwelling can be unlinked. (leave links to locations and institutions.)
  3. Categories may need to be adapted or removed - e.g. "people born in the 1940s". Redlinked categories are not a problem.
  4. Templates not used on Wikidwelling should be deleted, like all the interwiki links ({{de:...}}, {{fr:...}},
  5. When these first tasks are basically done, you can remove this template, writing {{Attrib Wikipedia | article name}} in place of this {{Attrib Wikipedia raw | article name}} at the bottom (simply remove "raw").
    You can also:
  6. Move to a section "External links" all Wikimedia project-related templates (e.g. {{Commons}}, {{Commons category}}, {{Wiktionary}}, etc. ).
  7. Add more specific content (related to the Wikidwelling topic) to the article, insert videos from YouTube, etc.

Pages with this template.

The original article was at Light tube. The list of authors can be seen in the history for that page. The text of Wikipedia is available under the CC-BY-SA 3.0 license.